|
Back to Product Categories
| 
 |
DSR-1800
DVCAM Studio Editing
Recorder/Player |
The DSR-1800 is the
successor model to the DSR-80. Implementing the innovative,
high standard technology featured in the DSR-2000, the
DSR-1800 boasts improved jog audio, slow motion and editing
performance. Two major features of these models are the
built-in jog/search dial and its multiple format playback
capability of DV (SP only) and DVCPRO 25. This unit has the
ability to automatically accommodate all 25 Mbps cassette
sizes, and does not require a cassette adapter or menu setting
changes for playback of these formats.
The DSR-1800
also has a full range of both analog and digital interfaces.
The availability of the SDI interface ensures a migration path
to Digital Betacam, Betacam SX and SDI-based systems. The SDTI
(QSDI) interface enable a quality deterioration-free transfer
between the DSR-1800 and DV compression-based systems. One new
option for this line is the i. LINK™ IEEE-1394 DV I/O
connection capability, which is useful for transferring
digital video between the DSR-1800 and compatible DV I/O
equipped cameras, VTRs and nonlinear editing systems.
The
DSR-1800 is the successor model to the DSR-80. Implementing
the innovative, high standard technology featured in the
DSR-2000, the DSR-1800 boasts improved jog audio, slow motion
and editing performance. Two major features of these models
are the built-in jog/search dial and its multiple format
playback capability of DV (SP only) and DVCPRO 25. This unit
has the ability to automatically accommodate all 25 Mbps
cassette sizes, and does not require a cassette adapter or
menu setting changes for playback of these formats.
The
DSR-1800 also has a full range of both analog and digital
interfaces. The availability of the SDI interface ensures a
migration path to Digital Betacam, Betacam SX and SDI-based
systems. The SDTI (QSDI) interface enable a quality
deterioration-free transfer between the DSR-1800 and DV
compression-based systems. One new option for this line is the
i. LINK™ IEEE-1394 DV I/O connection capability, which is
useful for transferring digital video between the DSR-1800 and
compatible DV I/O equipped cameras, VTRs and nonlinear editing
systems.
Features
PCM Digital
Audio:
The DSR-1800
provides excellent PCM digital audio performance with a wide
dynamic range and an excellent signal-to-noise ratio. There
are two selectable audio recording modes: 2CH mode with 48
kHz/16-bit or 4CH mode with 32 kHz/12-bit.
Playback Compatibility with DV (25 Mbps)
Formats:
The DSR-1800
offers excellent playback compatibility with DV family formats
(25Mbps). The DV family formats include DVCAM, DV (SP mode
only) and DVCPRO 25*. These tapes can be played back and
utilized directly as editing materials with +/-0 Frame
accuracy.
*Playback signal of DVCRO recorded tape is not
available via SDTI(QSDI) and i.LINK
interfaces.
Triple-positioning Cassette
Compartment:
Triple-positioning cassette compartment
automatically accepts DVCPRO M-size cassette tapes in addition
to standard and mini size cassette tapes of DV, DVCAM and
DVCPRO. Cassette insertion is done without the need for an
external adapter, or the need to set the playback format mode
before use.
Built-in
Jog/Shuttle Dial:
A highly
responsive Jog/Shuttle dial is built in on the front panel.
This feature is ideal for searching for desired edit
points.
Digital Slow Motion
and Jog Sound:
The DSR-1800
offers a variable speed playback function with a range of -0.5
to +0.5 times normal speed. Play back of digital noiseless
slow motion pictures and jog sound is also possible within
this range. This enables the fast and accurate locating of
edit pointson the tape. This feature is available for all DV
(25Mbps) format recorded tapes.
Frame Accurate Editing:
The DSR-1800 is equipped with an RS-422A remote
control connection to interface with the other compatible
equipment. i.LINK based control is also available by
installing the DSBK-1803 board. Frame accurate editing is
possible through either interface.
DMC (Dynamic Motion
Control):
By utilizing a
DMC-capable editing controller, the DSR-1800 can vary the
playback speed for a certain section of a tape in the range of
-0.5 to +0.5 times normal speed. Segments can be stored in
memory for playback at the same speed. NOTE: DMC is not
available through i.LINK and SDTI(QSDI) due to minute speed
video data processing capability.
Clip Link Operation:
By integrating the DSR-1800 into a non-linear
editing (NLE) system which supports ClipLink operation, the
VTR is able to send ClipLink information data onto the NLE
unit, providing great efficiency throughout the editing
process.
Process Control
(Video Control):
The
DSR-1800 is equipped with Process Control for both analog and
digital outputs in order to obtain highly stable video
signals. With Process Control, the video level, chroma level,
hue, Y/C delay Sync phase, SC phase and Set up (black) for
composite, S-video, component and SDI outputs can be
controlled through the VTR menu. These features can also be
adjusted from an external TBC remote controller through Video
Control port (D-sub 15-pin) on the rear panel.
VITC Time Code:
The DSR-1800 supports time code in the sub code
area on a tape, and also VITC through all video signal
interfaces. This time code is recorded on the video tracks.
VITC output is achieved by inserting the signal into the
vertical-blanking interval. The time code in sub code area can
also be output as VITC.
Audio Editing
Capabilities:
Audio
cross-fade function is available for noiseless audio
transitions at editing points. Audio mix/swap and voice-over
functions are possible without any delay between the video and
studio signals. In addition, all four audio channels can be
edited independently, which is applicable in creating or
editing video material in multiple languages, or implementing
multiple audio sources.
Built-in Signal
Generator:
The DSR-1800 is
equipped with a built-in signal generator, which can generate
color bars or black burst for video, and 1 kHz tone or mute
signal for audio. This is very convenient for creating
pre-striped tapes before editing.
Universal Powering
System:
The DSR-1800 is
equipped with a universal powering system that can accommodate
AC 100V to 240V, 50 or 60 Hz . A built-in regulator switches
the unit to the appropriate voltage automatically. This allows
the DSR-1800 to be used worldwide without the need for a
transformer.
Auto Repeat
Function:
Auto repeat
function is available through the VTR menu. Time code can also
be set as start and stop points.
Channel Condition
Monitoring:
The DSR-1800
has a three-color channel condition indicator, with each color
representing a particular error rate threshold level. This
function enables operators to quickly recognize the condition
of a VTR or tape for more reliable editing
operation.
DVCAM Digital
Component Recording Format:
The DVCAM format uses 8-bit digital component
recording with a 5:1 compression ratio and a sampling rate of
4:1:1. The DV compression algorithm provides excellent picture
quality and superb multigenerational
performance.
Specifications
Power
requirements:
AC 100-240V, 50/60 Hz
Power
consumption:
Approx. 100 W (DSR-1800 with all option
boards)
Dimensions (WxHxD):
16 7/8" x 7 x 19 5/8
inches
Weight:
28 lb. 10 oz
Operating
temperature:
32°F to 104°F
Storage
temperature:
-4°F to 140°F
Operating relative
humidity:
Less than 80%
Storage relative
humidity:
Less than 90%
Tape speed:
28.193
mm/s
Recording/playback time:
Standard
size: More than 184 min. with PDV-184ME
Mini size:
More than 40 min. with PDVM-40ME
FF/REW
time:
Standard size: Less than 3
minutes
Mini size: Less than 1
minutes
Search speed:
Max. 85 times normal
speed, forward and reverse via RS-422A
Ref. Video
Input:
BNC x 2, loop-through connection
0.286 Vp-p,
75W, sync negative
Composite Input:
BNC x 2,
loop-through connection
Composite, 1.0 Vp-p, 75W, sync
negative
Component Input:
BNC x 3
Luminance:
1.0 Vp-p, 75W, sync negative
Chrominance R-Y: 0.7 Vp-p,
75W
B-Y: 0.7 Vp-p, 75W
S-Video Input:
DIN 4pin
x 1
Y: 1.0 Vp-p, 75W, sync negative
C: 0.286 Vp-p, 75W
(at burst level)
SDI Input(using DSBK-1801 optional
board):
BNC x 2
Conforms to SDI (270 Mbps), SMPTE
259M
SDTI(QSDI) Input (using DSBK-1802 optional
board):
BNC x 1
Conforms to SDTI (270 Mbps), SMPTE
305M/322M
i.LINK (DV In/Out) (using DSBK-1803 optional
board):
6pin x 1
IEEE-1394-based (100
Mbps)
Audio Input:
XLR 3-pin female x
4
AES/EBU Input (using optional DSBK-1801):
BNC x
2
Conforms to AES-3id-1995
Time Code
Input:
BNC x 1
Ref. Video Output:
BNC x
1
0.286 Vp-p, 75W, sync negative
Composite
Output:
BNC x 2
Composite, 1.0 Vp-p, 75W, sync
negative
Component Output:
BNC x 3
Luminance:
1.0 Vp-p, 75W, sync negative
Chrominance R-Y: 0.7 Vp-p,
75W
B-Y: 0.7 Vp-p, 75W
S-Video Output:
DIN
4pin x 1
Y: 1.0Vp-p, 75W, sync negative
C: 0.286Vp-p,
75W (at burst level)
SDI Output (using DSBK-1601 for
DSR-1600):
BNC x 2, active-through
Conforms to SDI
(270 Mbps), SMPTE 259M
SDTI (QSDI) Output (using
DSBK-1602 for DSR-1600):
BNC x 1
Conforms to SDTI
(270 Mbps), SMPTE 305M/322M
i.LINK connection (DV
In/Out) (using DSBK-1803 optional board):
6-pin x
1
IEEE-1394-based (100Mbps)
Audio Output:
XLR
3-pin male x 4
Audio Monitor Output:
RCA Phono
jack x 1
Headphone Output:
JM-60 stereo phone
jack x 1
AES/EBU Output:
BNC x 2
Conformed to
AES-3id-1995
Time Code Output:
BNC x
1
RS-422A:
D-sub 9-pin x 1
Video
Control:
D-sub 15-pin x 1
Control S
(SIRCS):
Stereo mini jack x
1 |
